MIDI/USB 256 SWITCH 16 POTENTIOMETER ENCODER



Description:

This switch encoder is capable of encoding any number of momentary action, push to make, single pole single throw (SPST), switches from 1 up to 128 on MIDI Channel 1 and switches from 1 up to 128 on MIDI Channel 2, to produce the equivalent MIDI note-on/note-off data commands.The encoded switches are wired via IN4148 diodes. Any unrequired/unused switches can be left unconnected.

This unit can work in standard MIDI mode and via the USB connection. It defaults to standard MIDI Baud rate of 31250. By replacing the original firmware on Mega8u2/16U2, the Arduino Uno will act as USB-MIDI device (Standard Midi Class), you do not need to install additional device drivers on Windows, MaxOSX, and Linux, as the firmware acts as a device of Standard Midi Class. It will automatically install on the system as an Audio USB Device.

MIDI 128 Switches Encoder Channel 1 Wiring:

The switches are organized in a 16 x 8 matrix (up to 128 switches) arrangement. Note if less than 128 switches are required, then ONLY the switches required need to be wired.

The lowest note is switch SW0 wired via diode D0 between Pins 22 and 23 of the Arduino MEGA.

The next note is switch SW1 wired via diode D1 between Pins 24 and 23 of the Arduino MEGA.

The next note is switch SW2 wired via diode D2 between Pins 26 and 23 of the Arduino MEGA.

The next note is switch SW3 wired via diode D3 between Pins 28 and 23 of the Arduino MEGA.

The next note  is switch SW4 wired via diode D4 between Pins 30 and 23 of the Arduino MEGA.

The next note is switch SW5 wired via diode D5 between Pins 32 and 23 of the Arduino MEGA.

The next note is switch SW6 wired via diode D6 between Pins 34 and 23 of the Arduino MEGA.

The next note is switch SW7 wired via diode D7 between Pins 36 and 23 of the Arduino MEGA

Pin 22 is also looped to the Anodes of 15 other Diodes D8, D16, D24, D32, D40, D48, D56, D64, D72, D80, D88, D96. D104, S112,  and D120.

Pin 24 is also looped to the Anodes of Diodes D10, D19, D28, D37, D46, D55, D64, D73, D82, D91 and D100.

The other 7 pins 24,  26, 28, 30, 32, 34 and 36 are wired in a similar manner to the other Diodes.

Pin 23 is connected to switches SW0 to SW7,

Pin 25 is connected to switches SW8 to SW15,

Pin 27 is connected to switches SW16 to SW23,

Pin 29 is connected to switches SW24 to SW31,

Pin 31 is connected to switches SW32 to SW39,

Pin 33 is connected to switches SW40 to SW47,

Pin 35 is connected to switches SW48 to SW55,

Pin 37 is connected to switches SW56 to SW63,

Pin 39 is connected to switches SW64 to SW71,

Pin 41 is connected to switches SW72 to SW87,

Pin 43 is connected to switches SW88 to SW95,

Pin 45 is connected to switches SW96 to SW103,

Pin 47 is connected to switches SW104 to SW111,

Pin 51 is connected to switches SW112 to SW119,

Pin 53 is connected to switches SW120 to SW127.

Each of the other side of these group of 8 switches (eg SW0 to SW7 etc.) is wired to a diode on the Cathode (K) side (end of diode with stripe).

The other side of each of these diodes is looped to  other diodes. 

The MIDI 128 Switches Encoder Channel 2 Wiring is done in a similar manner.

The 16 Potentiometers:

The 16 Potentiometers are split into 2 groups of 8 each on MIDI Channels 1 and 2.

IMPORTANT NOTE:  It is important to connect any unused Analog Inputs to Ground (GND) to prevent electromagnetic noise and interference producing spurious MIDI Outputs.

Power Supply:

External power can come either from an AC-to-DC adapter or battery. The adapter can be connected by plugging a 2.1mm center-positive plug  into the board's power jack.

The board can operate on an external supply of 7 to 20 volts. If supplied with less than 7V, however, the 5V pin may supply less than five volts and the board may be unstable. If using more than 12V, the voltage regulator may overheat and damage the board. The recommended range is 7 to 12 volts.


Features:

The MIDI/USB 256 SWITCH 16 POTENTIOMETER ENCODER unit consists of:
  • An assembled, built and tested Arduino board including a suitable pre-programmed microcontroller,
  • The velocity byte is preset to a value of 100,
  • The MIDI channel is preset to 1 and 2,
  • Other channels and velocity values can be pre-programmed into the firmware on request,
  • 128 Switch Inputs on MIDI Channel 1,
  • 128 Switch Inputs on MIDI Channel 2,
  • 8 Potentiometer Inputs on MIDI Channel 1,
  • 8 Potentiometer Inputs on MIDI Channel 2,
  • A 2.1mm power socket, and associated LED,
  • A MIDI activity LED,
  • A 150mm wired MIDI 5-pin DIN output socket and associated resistors.
The MIDI/USB 256 SWITCH 16 POTENTIOMETER ENCODER unit requires:
  • a 9v battery or equivalent DC power source or USB,
  • Suitable switches and associated IN4148 diodes,
  • Suitable potentiometers (between 10k ohm and 1M ohm).

Resources:

The MIDI/USB 256 SWITCH 16 POTENTIOMETER ENCODER Unit Resources:
MIDI/USB 256 SWITCH 16 POTENTIOMETER ENCODER

ITEM#: MIDI/USB 256 SWITCH 16 POTENTIOMETER ENCODER

PRICE:  €79.95

After clicking on the 'Add to Cart' button, just complete your order on the Paypal site, where you can select the required quantity. Also the appropriate shipping cost is calculated and added. However you may still cancel or adjust your order, at this point.